詳解雙組份打膠機比例泵密封圈
1.雙組份打膠機因為中空玻璃打膠機密封膠的固化需要必定時間，因此 雙組份打膠機，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. Two component gluing machine because the gluing of insulating glass and the curing of sealing glue need a certain time, so the glass coated with two-component sealant should be moved horizontally and gently.
2.A組、B組份膠應保持清潔，謹防異物進入膠中。
2. The glue of group A and B shall be kept clean to prevent foreign matters from entering the glue.
3. 雙組份打膠機在連續作業過程中，膠槍每次停止作業時間一般不得超過20分鐘，不然，應用A組份膠沖出全部混合膠，直單一的A組份膠從槍口排出停止。
3. During the continuous operation of the two-component glue applicator, the operation time of the glue gun shall not exceed 20 minutes each time. Otherwise, all the mixed glue shall be washed out with component a glue until a single component a glue is discharged from the muzzle.
4.雙組份打膠機高壓膠管不得強行揉捏、彎曲，防止影響系統正常作業。
4. The high-pressure hose of the two-component gluer shall not be kneaded or bent forcibly to prevent affecting the normal operation of the system.
5.混膠器應經常保持通暢，以確保良好的出膠作用。如遇堵塞情況，可用丙酮浸泡后清洗。主張每5組清洗一次。
5. The mixer shall be kept unobstructed frequently to ensure good glue delivery. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.
6.當膠槍長期不用時(超過一周)，應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the glue gun is not used for a long time (more than one week), remove the gun body and clean the residual colloid in the glue gun and mixer with solvent.
7.不同中空玻璃打膠機出產廠家所出產的膠內含雜質數量不同，依據實際情況明晰B組分的過濾網及單向止回閥，主張每兩組清洗一次。
7. The quantity of impurities in the glue produced by different manufacturers of insulating glass gluing machine is different. The filter screen and one-way check valve of component B shall be clarified according to the actual situation, and it is advocated to clean every two groups.
8.任何因膠體固化所形成的膠槍、管路或整機的故障 雙組份打膠機，一概不在保修范圍之內。
8. Any failure of glue gun, pipeline or the whole machine caused by colloid solidification. The cost of two-component glue applicator is not within the scope of warranty.
9.定期給雙組份打膠機各泵的加油口加油中空玻璃打膠機，應確保油霧器內不斷油。
9. Regularly add oil to the oil filler of each pump of the two-component glue applicator. The insulating glass glue applicator should ensure that there is continuous oil in the oil mist.
The above is the knowledge brought to you today. Jinan two-component gluing has focused on the industry for many years and continuously provided users with valuable content. Please continue to pay attention to us for more content: http://www.cztaiyue.com
上一篇：什么情況下會導致打膠機打膠不均勻？
下一篇：自動打膠機的特點有哪些？
