雙組份打膠機要注意安裝順序
、雙組份打膠機設備應安裝在干燥、無粉塵、無腐蝕性氣體的壞境中（該要求與其他設備一致，當然如果條件達不到少爭取無腐蝕性氣體，畢竟設備中有電線以及管路這些配件抗腐蝕性不高）。
The two-component glue applicator equipment shall be installed in a dry, dust-free and corrosive gas free environment (this requirement is consistent with other equipment. Of course, if the conditions are not met, at least strive for no corrosive gas. After all, there are wires and pipelines in the equipment, and the corrosion resistance of these accessories is not high).
、室內溫度更好控制在10～40度的室內堅硬地面上，地面應水平度要好。（小編這里說的地面水平度要好不一定要非常的平整才行，我們的設備在設計之初已經考慮到了地面復雜性的因素所以對地面平整度是有相當大的容忍度的，只要不是幅度提別的大一般都可以正常工作。）
The indoor temperature shall be better controlled on the indoor hard ground of 10 ~ 40 degrees, and the ground shall be better leveled. (Xiaobian said that the ground levelness here must be very flat. Our equipment has taken into account the complexity of the ground at the beginning of design, so we have a considerable tolerance for the ground levelness. As long as it is not too large, it can generally work normally.)
、雙組份打膠機安裝之前，應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況，之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備不能正常運行，我們的工作人員到現場后才排查出的原因。
Before installing the two-component glue applicator, we should first check whether there is deformation, damage and fastener looseness caused by transportation and moving. Previously, a customer knocked off a part of the intelligent control system of the equipment in the process of moving the glue applicator, which led to the abnormal operation of the equipment. Our staff found out the reason after arriving at the site.
1、我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地，把氣源接入機器所配帶的氣源接口，確保無漏氣現象。
1. Firstly, we can adjust the levelness of the equipment by adjusting the lifting anchor bolts of the equipment according to the actual situation of ground flatness until the equipment is horizontal and stable. Then connect the wiring according to the diagram and reliably ground, and connect the air source to the air source interface equipped with the machine to ensure that there is no air leakage.
2、向油槽中加注液壓油指定位置，46#液壓油（約為50升左右）。
2. Fill the oil tank with hydraulic oil to the specified position, 46# hydraulic oil (about 50 liters).
3、接通電源并打開查看設備是否能夠正常運行。
3. Turn on the power and turn it on to see if the device can operate normally.
The wonderful content of this article is provided by the two-component glue applicator. Please pay attention to more content http://www.cztaiyue.com
上一篇：雙組份打膠機的檢修注意點
下一篇：打膠機跟灌膠機的區別
