混膠機控制出膠量的有效方式

濟南雙組份打膠機在更換膠管時，注意不要把空氣引入到膠體通道中。如果膠管中有空氣殘留，而你又確定空氣沒有通過膠管進入灌膠泵中。針對灌膠系統：排膠要有足夠時間，使新膠管中的膠體順利流出灌膠頭，確認灌膠閥的壓力和速度按照理想狀態設定。然后測定膠體流速，直連續兩次測量結果的誤差在正負 2% 范圍以?xún)?nèi)。
When replacing rubber hoses, the two component glue machine in Ji'nan is careful not to introduce air into colloidal passages. If there is any residual air in the hose, you will make sure that the air does not pass through the hose into the filling pump. For the glue system: the glue should have enough time to make the colloid in the new rubber tube out of the glue head smoothly and confirm the pressure and speed of the filling valve according to the ideal condition. Then the flow rate of colloid was measured until the error of two successive measurements was within the range of positive and negative 2%.
1、利用體積來控制，也就是活塞，體積到了一定的程度，活塞自動切斷進料。
1, the volume control, that is, the piston, to a certain extent, the volume of the piston automatically cut off feed.
2、利用點膠控制器，只要我們對高精密的點膠閥進行控制，就可以達到點膠機出膠量的大小。
2, using glue dispenser, as long as we control the high-precision dispensing valve, we can achieve the size of dispensing machine.
3、出膠壓力，壓力的大小我們可以通過調節調壓閥來控制壓力的大小，只要?dú)庠吹膲毫Ψ€(wěn)定，那么出膠的壓力自然也就穩定了。
3, out of the pressure, the size of the pressure we can adjust the pressure valve to control the size of the pressure, as long as the pressure of the gas source is stable, then the pressure of the glue is naturally stable.
4、通過控制出膠時間，如果出膠時間設置的越長，那么出膠量就越大，反之，則越小。
4, by controlling the gel time, the longer the dispensing time is, the larger the amount of gel will be, and the smaller it will be.
以上的介紹，您了解了嗎？如果您有不明白的地方，歡迎您的致電，我們?yōu)槟榻B，歡迎您的蒞臨參觀哦。
Do you know the above introduction? If you do not understand, please call us. We will introduce you to you. Welcome to visit us.

上一篇：雙組份打膠機使用操作流程
下一篇：詳解雙組份打膠機日產量多少？